What do you do when your garage door suddenly stops functioning?

What do you do when your garage door suddenly stops functioning?

wall stud

What Type of Garage Door Opener and Door Do You Have? What should you do when the garage door stops working? .


It is important to know the kind of garage opener and door that you are using before you begin troubleshooting.


Garage doors generally fall into different categories according to their design and operation.The most popular kinds are roll-up, sectional and tilt-up doors.Sectional doorways are constructed from panels that are joined by hinges, allowing the doors to bend as it closes and opens on the vertical track.Roll-up doors, often found in commercial settings made from slats that roll up into a coil.

The tilt-up door, on contrary, is a solid, single piece that opens by tilting outward upwards.

It is equally important to identify the type of garage door opener.The three types of garage door openers include belt-drive and chain-drive and screw-drive openers.Chain-drive openers, which use chains of metal to raise and lower the door, are durable and affordable but they are noisy.Belt-drive openers function similarly, however, they employ a rubber belt, making them quieter and an ideal choice for attached garages.Screw-drive openers move the door by means of a threaded steel rod that provides a balanced balance between the noise and the cost.


The next step is to examine the garage door opener and identify the model. Make sure to check the breaker and plug to ensure that the opener is powered. Examine the release cord for manual operation to be sure that it's not been pulled. This could result in the door being disconnected from the opener. Examine the rollers and tracks of the door to determine if there are damage or obstructions. Remove any obstructions.

If needed, you should lubricate the moving parts. Insufficient lubrication could cause them to jam or become stuck.

Resetting the opener will fix any electronic malfunctions. Read the manual of the opener you're using to determine the precise steps. Some openers can be reset with a push of a button while others require that the unit not be plugged in and then re-plugged.


In certain instances it could be more complex like a damaged spring or a motor that is worn out that requires professional assistance.Springs are subject to significant tension, and they can be dangerous to repair without the proper equipment and knowledge.


If the garage door stops functioning or is not working, it's best to consult an expert.

Check for Obstructions or Debris


It's not easy and perplexing when your garage door ceases to function in a flash, especially if frequently use it.

One of the primary and most efficient steps you can consider when you are faced in this scenario is to examine the door for any obstructions or debris.This easy, yet efficient action can often be the key to identifying the problem and restoring functionality to the garage door.

A small obstacle could hinder your garage door from functioning properly.


Begin by visually examining the tracks that run along both sides of the door.Look for obvious obstructions or buildup of debris.If you find anything that is unusual, such as a twig or a stone stuck to the track, make sure you remove it.

Sometimes, the issue may not be immediately visible, so it's advisable to run your hands across the track to look for any undetected obstacles.Ensure that the tracks are aligned correctly too, since a in the event of a misalignment, it could result in the door becoming jammed.

After that, examine the rollers and hinges. They should be free to move without a thump. If they're stuck or sticky, it could be due to corrosion or grime. Lubricating and cleaning these parts can typically solve the issue.


It's also vital to look over the area around the door itself.Sometimes things stored in the garage could accidentally be moved or fall off, blocking the route of the door.Ensure that the area is clean and that there's nothing that is hindering the door's movement.




What do you do when your garage door suddenly stops functioning? - river

  1. wall stud
  2. river
  3. Ashburn
If, despite clearing any obvious obstructions, the door still refuses to work, consider checking the sensors.

The sensors that are fitted to modern garage doors may malfunction when they're dirty, or if they are not aligned correctly.

By keeping your walkway clean and by avoiding obstructions, you'll avoid having to contact a professional fix a problem that is often easy to fix.

Verify the wall switch as well as the remote control


It's crucial to examine the wall switch as well as the remote control.

Examining these components can help you save time and prevent costly errors.

First, consider the remote control.This handheld device is your primary tool for operating the garage door without direct physical interaction.Over time, remote controls can experience issues such as drained batteries, signal interference, or even internal damage.Start by replacing the batteries with new ones.It might seem simple, but dead batteries are a common reason for a garage door not responding.If the problem persists after replacing the batteries, try reprogramming the remote according to the manufacturer's instructions.Additionally, ensure that the remote is within the recommended range and that there are no obstructions blocking the signal.

What do you do when your garage door suddenly stops functioning? - wall stud

  1. Zumba
  2. diameter
  3. metal


Next, turn your attention to the wall switch, which is a important component of the garage door system.

If you are comfortable you are comfortable, then open the switch to inspect for any damaged or broken wires.

The wall switch or the remote control could be functioning properly however the door not yet working. This could mean that there is a problem with the garage opener or with other parts, like sensors or tracks.

You can resolve these issues before you begin more difficult troubleshooting.

The initial check will help you save time and give you peace of mind that you've taken the proper steps to identify the issue.

Test the door balance manually


When your garage door suddenly stops working, it can be both annoying and inconvenient.The garage door is a vital part of your home, providing security, shielding from elements, and easy access to your car and storage area.

One important step to consider when you encounter a malfunctioning garage door is to manually test the door's balance.This simple, yet powerful procedure can help diagnose potential issues and prevent further damage to the door and its components.

The balance of a garage door is critical to its correct operation. An imbalanced door can create more serious issues such as misalignment, broken springs.


To manually test the door balance, you must first disconnect the garage door opener.

The majority of garage doors come with a release mechanism. It is typically a red cord or handle which allows you to disengage the door from the motor.Once the door has been disconnected, carefully lift it manually up to around waist-high, then let it go. it.A well-balanced door will remain stationary or move very slowly.If the door begins to fall quickly or shoots upwards this indicates an imbalance.

If you discover that the door isn't balanced it is vital to resolve the issue promptly.Door balance problems are typically related to the tension of the springs, which can be dangerous to adjust on your own due to the pressure they're under.It is recommended that you get help from a professional to adjust the springs to ensure that the door is properly balanced correctly.Doing so not only resolves the immediate issue but also will increase the longevity and stability of the garage door system.

What do you do when your garage door suddenly stops functioning? - wall stud

  1. Cairo
  2. education
  3. volleyball


Testing the balance manually on your garage door is a vital first step to make if it suddenly stops functioning.

When you take action quickly and recognizing the importance of each to address them quickly, you can ensure your garage door will operate seamlessly and safely in future.

Examine the Tracks and Rollers

This simple check will reduce your expenses and save you time If your garage door not working.


Tracks and rollers are essential components of your garage door's operational system.The tracks comprise the metallic rails that direct the door when it opens and closes. The rollers are wheels of a smaller size which move along the tracks.

These components can wear out, become dirty or misaligned over time. This can lead to malfunctions.

Begin by looking over the track for obstructions. The accumulation of dirt, dust or even small pieces of debris can be accumulating, which causes rollers to struggle to travel along the path. Cleaning the tracks with an aqueous cloth will resolve this problem.


The next step is to check the alignment of the tracks.Tracks should be straight and parallel to each other.If they look bent or not in alignment, the door will jam.You can gently tap the misaligned portions back into their proper position with the help of a rubber mallet.However when the damage is severe and extensive, you should consult a professional to adjust them in a safe way to ensure security and functionality.


The rollers may wear out over time. This is especially true in the case of plastic.

Examine for indications of wear and tear, for example, cracks or chips.If the rollers look worn, think about changing them out with brand new ones.Metal rollers equipped with ball bearings typically offer greater durability and smoother operation.

The use of silicone-based lubricants will decrease friction and wear. It is important to oil the hinges as well as the springs to ensure your garage door functions efficiently.


In conclusion, examining the rollers and tracks is a sensible first step if the garage door suddenly ceases working.It's an easy process that can frequently identify and solve frequent issues.By making sure that these parts are clean, aligned and well-lubricated, you can usually restore your garage door fully functional without having to pay for costly repairs.

It is important to periodically check and maintain these parts can also prevent any future issues, extending the life of the garage door system.

Verify for visible damage, or wear

It can be frustrating and a hassle when garage doors stop completely, especially when you're on your way home or trying to secure your house for the night.


Garage doors are complex systems that comprise rollers, springs tracks, cables, as well as other components. With time, the components of this system will get worn out from regular use and exposure.

If you conduct a thorough visual check, you will be able to spot any obvious signs of damage creating problems for the door.

Begin by examining springs. They are responsible for lifting and lower the door. Look for indications of wear or rust. A worn or damaged out spring could render the door inoperable, therefore it's essential to fix the issue as soon as possible. In the next step, inspect the cables for fraying or broken cables.


The door is another place which requires focus. Examine for visible warping, dents, or bends.

Check that the sensors on the door are cleaned and in good alignment. A misalignment or dirt build-up could cause them to malfunction and stop functioning.

While a visual inspection can give valuable information but it is crucial to consider that some problems might not be immediately apparent.If you don't see any obvious indications of wear or damage, it might be necessary to talk with a professional to identify and fix the problem.However it is possible to conduct an initial inspection, you'll be able to identify and address minor issues prior to them escalating into significant and costly repairs.


In summary, when faced with an unusable garage door, checking at the visible signs of wear and tear is a crucial first step.This technique not only aids to identify the issue fast but also enables you to take the necessary action to bring the door back to its proper functioning.

If you are proactive and alert to your garage door's needs, you can guarantee the longevity and security of your garage door

Check the Springs and Cables

When your garage door suddenly stops working, it can be both difficult as well as inconvenient.One of the most crucial actions you can take in this situation is to examine the springs and cables.These parts are crucial for the proper functioning of your garage door and any issues with them are often the culprits behind a broken door.


The springs play an important role in the operation and smoothness of your garage through neutralizing the load. There are two main types of springs: extension and torsion. Torsion springs mount above the garage and then twist in order to store energy. Extension springs on the other hand are installed on at either end of the door and extend to provide necessary force.

As time passes, these springs can wear down, break, or lose tension, which can lead to issues with operation.

The cables could also be damaged through wear and tear. They may fray or snap under the pressure.


If you are unsure whether the cables or springs require to be adjusted, visual look them over. Examine for signs of wear or rust.


Security is a must while dealing with garage door parts.

Cables and springs are under pressure and could result in serious injuries if mishandled.If you're not a pro at garage door repairs, it's wise to contact an experienced technician.They have the equipment and experience to safely fix or replace these components and ensure that your garage door is operating correctly and securely.

In conclusion, when your garage door suddenly stops working, assessing the springs and cables is a key step in diagnosing the problem.Understanding their role and potential issues can help you determine whether a simple adjustment is needed or if professional intervention is required.Taking prompt action not only restores functionality but also ensures the safety and longevity of your garage door system.

It is recommended to call a professional Technician


Garage doors can suddenly stop functioning and cause you to lose your time. It may even cause your home to be at risk.

Although it may be tempting to grab the tools and attempt a do-it-yourself fix The most sensible option is to think about calling a professional technician.This decision will not only guarantee your safety but also offers a more effective and lasting solution to the issue.

Garage doors are complex systems composed of various components such as springs, cables, tracks, and electronic parts.Each of these elements plays a crucial role in the door's operation, and a malfunction in any part can cause the entire system to fail.Without proper knowledge and experience, attempting to fix these issues can be dangerous.For instance, garage door springs are under high tension and can cause severe injury if handled improperly.Professional technicians are trained to deal with these risks safely, using the right tools and techniques to handle repairs.


Moreover, a professional technician is a skilled professional with experience and knowledge that a layperson does not possess.

They can quickly diagnose the issue and identify whether it's a minor problem, like a misaligned track, or something more serious, like a broken spring.This expertise not only saves you time but also prevents the potential for further damage that can occur with incorrect handling.Professionals also have access to high-quality parts and can ensure that replacements match the specifications of your existing garage door system, leading to better functionality and longevity.

A professional technician can also be cost-effective over the long haul. Although an DIY approach may seem cheaper at first, it can result in larger and more expensive repairs later.

Most technicians offer warranties for their services. This gives you confidence that should something go wrong, the problem is protected.

A professional can save you significant time and hassle.Trying to master the intricate details of garage door mechanics, buy the right tools, and carry out the repair could take hours or even days.In the opposite, a technician will often be able to resolve the issue quickly, allowing you to go back to normal without unneeded delays.


While the urge to fix your garage door yourself might be strong, calling an expert technician is the safest best, most efficient, and ultimately, the best option.Their expertise in locating quality parts, and the ability to complete quick and precise repairs will ensure that your garage door is back and running at a high level and will protect your home and

Citations and other links

Village of Mokena
The gable bank barn at the historic McGovney–Yunker Farmstead
The gable bank barn at the historic McGovney–Yunker Farmstead
Flag of Village of Mokena
Official seal of Village of Mokena
Motto(s): 
Planned Progress, Pleasant Living
Location of Mokena in Will County, Illinois.
Location of Mokena in Will County, Illinois.
Location of Illinois in the United States
Location of Illinois in the United States
Coordinates: 41°32′04″N 87°52′37″W / 41.534414°N 87.876873°W / 41.534414; -87.876873
CountryUnited States
StateIllinois
CountyWill
TownshipFrankfort, New Lenox
Incorporated1880
Government
 • TypeVillage
Area
 • Total8.68 sq mi (22.47 km2)
 • Land8.68 sq mi (22.47 km2)
 • Water0.00 sq mi (0.00 km2)
Population
 (2020)
 • Total19,887
 • Density2,292.19/sq mi (885.05/km2)
Time zoneUTC-6 (CST)
 • Summer (DST)UTC-5 (CDT)
ZIP code
60448[2]
Area codes708
FIPS code17-49854
Websitehttp://www.mokena.org/

Mokena (/mˈkinə/ moh-KEE-nuh) is a village in Will County, Illinois, United States. It is a southwest suburb of Chicago. The population was 19,887 at the 2020 census. The Census Bureau's 2019 estimate found that the population had increased to 20,159.[3]

Etymology

[edit]

Mokena is a name apparently derived from a Native American language meaning "turtle".[4] While the particular language from which the name originates is not documented, likely candidates are Anishinaabemowin, whose word for "snapping turtle" is mikinaak,[5] and its close sister language Potawatomi, in which the same animal is called mkenak.[6] Both languages were once spoken in the area now occupied by the town.

Mokena is located at 41°32′4″N 87°52′37″W / 41.53444°N 87.87694°W / 41.53444; -87.87694.[7] According to the 2010 census, Mokena has an area of 8.893 square miles (23.03 km2), of which 8.89 square miles (23.02 km2) (or 99.97%) is land and 0.003 square miles (0.01 km2) (or 0.03%) is water.[8] It is bordered by Tinley Park to the northeast, Orland Park to the north, Homer Glen to the northwest, Frankfort to the south and New Lenox to the west.

Education

[edit]

Elementary school services are provided by one of four school districts: Mokena School District 159, New Lenox School District 122, Frankfort School District 157C, and Summit Hill School District 161. Schools within District 159 include MES (Mokena Elementary School), MIS (Mokena Intermediate School), and MJHS (Mokena Junior High School). Mokena is served by Lincoln-Way Community High School District 210; students living in districts 159 or 122 attend Lincoln-Way Central High School, and students living in districts 157C or 161 attend Lincoln-Way East High School. Higher education is provided at Joliet Junior College, the nation's first public community college, and at Rasmussen College.

Demographics

[edit]
Historical population
CensusPop.Note
1880522
1890364−30.3%
1900281−22.8%
191035927.8%
192047532.3%
193056218.3%
194065716.9%
195090337.4%
19601,33247.5%
19701,64323.3%
19804,578178.6%
19906,12833.9%
200014,583138.0%
201018,74028.5%
202019,8876.1%
U.S. Decennial Census[9]

As of the census[10] of 2010, there were 18,740 people, 6,358 households, and 5,120 families residing in the village. The population density was 2,432.4 inhabitants per square mile (939.2/km2). There were 4,848 housing units at an average density of 808.6 per square mile (312.2/km2). The racial makeup of the village was 94.5% White, 1.3% African American, 0.01% Native American, 2.0% Asian, 0.01% Pacific Islander, 0.9% from other races, and 0.63% from two or more races. Hispanic or Latino of any race were 4.8% of the population.

As of the census of 2000, there were 4,703 households, out of which 48.5% had children under the age of 18 living with them, 73.7% were married couples living together, 7.3% had a female householder with no husband present, and 16.8% were non-families. 14.0% of all households were made up of individuals, and 3.3% had someone living alone who was 65 years of age or older. The average household size was 3.10 and the average family size was 3.46.

In the village, the population was spread out, with 32.4% under the age of 18, 7.1% from 18 to 24, 32.7% from 25 to 44, 21.5% from 45 to 64, and 6.2% who were 65 years of age or older. The median age was 34 years. For every 100 females, there were 101.5 males. For every 100 females age 18 and over, there were 97.3 males.

The median family income is $82,596 and the median income for a household is $91,817. Males had a median income of $58,226 versus $31,522 for females. The per capita income for the village was $31,944. As of 2008, the median house value was $350,130, up from $211,300 in 2000.[11]

About 0.7% of families and 1.0% of the population were below the poverty line, including 0.6% of those under age 18 and 4.6% of those age 65 or over.

Transportation

[edit]

The Village of Mokena is serviced by the Metra rail service Rock Island District. Mokena has two commuter rail stations, Hickory Creek and Front Street, providing service to downtown Chicago's LaSalle Street Station, connecting with components of the Chicago Transit Authority. Mokena is also served by I-80, which runs along its northern border. Through I-80 commuters have convenient access to I-355 (Veteran's Memorial Tollway) and I-57. The main north–south thoroughfares are US Route 45 (LaGrange Rd) and Wolf Rd. The main east–west thoroughfares are 191st St, LaPorte Rd., and US Route 30 (Lincoln Highway). Rail freight traffic travels along both the Metra RI District Railway (Metra RI) and the Canadian National Railway (CN). The CN tracks run east/west along Mokena's southern boundary, while the Metra Rock Island District (Metra) tracks approximately bisect the town in a northeastern/southwestern direction.

Notable people

[edit]

References

[edit]
  1. ^ "2020 U.S. Gazetteer Files". United States Census Bureau. Retrieved March 15, 2022.
  2. ^ "Mokena IL ZIP Code". zipdatamaps.com. 2023. Retrieved January 26, 2023.
  3. ^ "2010 Census Interactive Population Search". Archived from the original on June 15, 2016. Retrieved December 6, 2017.
  4. ^ Gannett, Henry (1905). The Origin of Certain Place Names in the United States. U.S. Government Printing Office. p. 211.
  5. ^ "The Ojibwe People's Dictionary". ojibwe.lib.umn.edu. Retrieved January 7, 2021.
  6. ^ "Potawatomi Language Dictionary - View Word". potawatomidictionary.com. Retrieved January 7, 2021.
  7. ^ "US Gazetteer files: 2010, 2000, and 1990". United States Census Bureau. February 12, 2011. Retrieved April 23, 2011.
  8. ^ "G001 - Geographic Identifiers - 2010 Census Summary File 1". United States Census Bureau. Archived from the original on February 13, 2020. Retrieved December 19, 2015.
  9. ^ "Census of Population and Housing". Census.gov. Retrieved June 4, 2015.
  10. ^ "U.S. Census website". United States Census Bureau. Retrieved January 31, 2008.
  11. ^ "Mokena, Illinois (IL 60448) profile: population, maps, real estate, averages, homes, statistics, relocation, travel, jobs, hospitals, schools, crime, moving, houses, news, sex offenders". www.city-data.com.
  12. ^ "Boers: Leaving Home Produces Rush Of Vivid Memories". December 23, 2014. Retrieved January 4, 2020.
  13. ^ Sherdog.com. "Jason Guida MMA Stats, Pictures, News, Videos, Biography - Sherdog.com". Sherdog. Retrieved January 4, 2020.
  14. ^ 'Don C. Hall, 87, Veteran Show Trouper, Dies,' Stevens Point Daily Journal, October 29, 1953, pg. 15
  15. ^ "Ron Kittle: Renaissance Man | Chicagoly Magazine". Archived from the original on June 22, 2019. Retrieved June 22, 2019.
  16. ^ Sotonoff, Jamie (August 30, 2011). "Denise Richards: Suburban upbringing kept me grounded". Daily Herald.
[edit]

Sectional garage door
Up-and-over garage door
Torsion springs, drums, cables, end bearing plates, center bearing plate and rolloers (wheels) all hardware needed for a functional garage door.
Garage Door Hardware

A garage door is a large door to allow egress for a garage that opens either manually or by an electric motor (a garage door opener). Garage doors are frequently large enough to accommodate automobiles and other vehicles. The operating mechanism is usually spring-loaded or counterbalanced to offset the door's weight and reduce the human or motor effort required to operate the door. Less commonly, some garage doors slide or swing horizontally. Doors are made of wood, metal, or fiberglass, and may be insulated to prevent heat loss.

Description

[edit]
An electric garage door opener operates on the center track

A typical version of an overhead garage door used in the past would have been built as a one-piece panel.[1] The panel was mounted on each side with an unequal parallelogram-style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers.[1] The weight of the door may be 400 lb (180 kg) or more but is balanced by either a torsion spring system or a pair of extension springs.[2] A garage door opener is controlled motorized mechanism for opening garage doors adds convenience, safety, and security often used with a remote or a button on wall.[3]

History

[edit]

The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the United States, they arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]

Types

[edit]

Single panel garage doors

[edit]
jamb type hardware
one piece track type hardware

Single-panel doors are constructed from one monolithic panel. A single panel door swings up and overhead with a hinge on each side (jamb-type hardware) to a fully open position from the closed position. A disadvantage of monolithic panel doors is that the swing-up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.

Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (mounted at the top of the wood frame) and a roller mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of the garage door. Using track hardware, a car can be parked much closer to the door, as the door is positioned entirely inside the garage door header when in the open position. Track-type hardware has less arc when raising and lowering the garage door than jamb-type hardware.[citation needed]

Sectional garage doors

Sectional doors usually have three to eight panels and slide up and overhead. Sectional doors occupy the same internal garage space as a monolithic door. Sectional doors have two advantages over single-panel monolithic doors:

  • Sectional doors do not require any space outside the garage to open. A vehicle may park very close to the garage before opening the door.
  • Each panel of a sectional door has its connection to the door track. This increases reliability and robustness compared to monolithic doors, which have only a few track connections for the whole panel.

Garage doors can be made of many materials, but steel, aluminum, wood, copper, glass, and vinyl (polyethylene) are the most popular materials. Some manufacturers incorporate foamed-in-place polyurethane insulation within the monolithic panel and sectional garage doors.

The side sliding sectional door[5]

  • A lot of space under the garage ceiling.
  • Can use the entire ceiling of the garage.
  • Fast access to the garage

Roller doors

[edit]
Detail of roller door mechanism
Industrial tents with rollup overhead doors

Roller doors (sometimes called "sheet doors") are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g., transparent corrugated fiberglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single-car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Oversized roller doors in commercial premises are not sprung (except in the US), and a manual pulley and chain system or a geared motor is used to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.

In the UK (and other parts of the EU), 'insulated' roller garage doors are available, using an aluminum lathe filled with polyurethane foam for thermal and acoustic insulation.

Concerning thermal insulation, the roller door has a typical insulation R-value of 4.9 to 5.2. A sheet steel garage door has a typical insulation R-value of 0.5 to 2.7.

An application that needs more thermal insulation typically uses a foam-filled sectional garage door, which provides typical insulation R-values of 6.1 to 6.4.

Garage door materials

[edit]
  • Aluminum garage doors are usually found in commercial settings and are uncommon for residential ones. Aluminum is typically only used for full-view garage doors (doors that are made up of glass sections divided by aluminum stiles). Aluminum doors are rust-proof and low maintenance.
  • Fiberglass and vinyl garage doors are composite units, combining a steel core behind a fiberglass or vinyl skin. They also have polyurethane insulated base sections or other types of foam insulation. These premium doors can match steel garage doors and be a realistic imitation of wood (namely fiberglass units), but they may be more expensive than steel units. Fiberglass doors are commonly used near an ocean, where salt water can ruin regular steel doors.
  • Steel doors have a variety of sizes and styles, provide strength and security, are cost-competitive, and may have optional insulating value. Extra strength is available with two or three layers of galvanized steel with a low gauge number (0.6 - 0.7 mm steel panels).[6]
  • Wood garage doors offer aesthetic appeal, but they are high maintenance and may be expensive. Low-priced wood garage doors may warp and break easily.

Steel stamped construction

[edit]
Sectional-type steel with exterior cladding overhead garage doors in the style of old carriage house doors

A common material for a new garage door is a steel sheet formed or stamped to look like a raised panel wooden door. Steel doors are available in uninsulated, insulated, and a three-layer door, also known as a sandwich-style door. A design mimicking carriage house doors has become popular since the early 2000s, and many manufacturers clad the exterior of a steel door with composite, vinyl boards, or other trim to give it the appearance of wood.

Insulation

[edit]

In situations involving residential attached garages, the insulating value and the energy efficiency of a garage door are essential to avoid overheating and freezing problems, as well as for comfort and energy savings.

Torsion spring lift mechanism

[edit]

A torsion spring counterbalance system consists of one or two tightly wound-up springs on a steel shaft with cable drums at both ends. The apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs consist of a steel wire with a stationary cone at one end and a winding cone at the other. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind, and the stored tension lifts the door by turning the shaft, thus turning the cable drums and wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums, and the springs are rewound to full tension.

Life of torsion spring

[edit]

Garage door manufacturers typically produce doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000-cycle spring. However, it is essential to remember that if the garage door's weight is increased by adding glass, additional insulation, or even several coats of paint, the torsion spring's life may be significantly reduced. Additionally, springs in highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.

Other factors like poor garage door maintenance, loose tracks, or components shorten torsion spring life. Owners are advised to avoid applying grease to garage door tracks because that makes the wheels "skate" in the track instead of turning on their bearings. Only bearings, hinges, and spring wire require lubricant.

Extension spring lift mechanism

[edit]

An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically, these springs are made of 11 gauge (3 mm) galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.

Maintenance

[edit]

Maintenance of garage doors is described in the manufacturer's instructions and consists of periodic checks for correct operation, visual inspection of parts, and lubrication. [7][8]

Safety

[edit]

Garage doors can cause injury and property damage (including expensive damage to the door itself) in several ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings, and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on torsion spring systems).

A garage door with a broken spring or the wrong strength can fall. Because the effective mass of the door increases as the garage door sections transfer from the horizontal to vertical door tracks, a falling garage door accelerates rapidly. A free-falling garage door can cause severe injury or death.

The sections and rollers on garage doors represent a significant pinch hazard. Children should never be allowed near a moving garage door for this reason. On manually operated garage doors, handles should be installed vertically to promote "vertical orientation of the hand".

Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. Modern openers have “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lb (10 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door-related property damage, can be avoided by following these precautions.[9]

Certain parts, especially springs, cables, bottom brackets, and spring anchor plates, are under extreme tension. Injuries can occur if parts under tension are removed.

Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. The safety cable prevents hazards to bystanders when a spring, pulley, or cable breaks under tension and makes the system relatively safe.

Torsion spring systems can be hazardous as they are always under tension and release energy when the spring fails. Severe injury or death can be caused by the projectile pieces of a failed torsion spring. Many people have been injured or killed trying to adjust torsion springs, and special training and procedures are required to modify a torsion spring safely; it is a job for a professional, not a homeowner or DIYer.

References

[edit]
  1. ^ a b Hamilton, Gene; Hamilton, Katie (2004). Do it right the first time: what every homeowner needs to know before the work begins. Innova Publishers. p. 154. ISBN 9780974937359. Retrieved 2015-07-19.
  2. ^ Ask the Family handy-man. Reader's Digest. 1999. p. 138. ISBN 9780762101429. Retrieved 2015-07-19. garage door can weigh 400 pounds or more; they only seem light because the springs balance the weight as you lift the door.
  3. ^ Day, Richard (July 1982). "Tips from a pro: how to install a garage-door opener". Popular Science. Vol. 221, no. 1. pp. 91–93. Retrieved 2015-07-19.
  4. ^ a b Winterton, Deanne (2012-02-21). "History of the Garage Door". Amazines.com. Retrieved 2015-07-19.
  5. ^ Deziel, Chris (10 October 2023). "Are Sliding Garage Doors the Best Option for You?". Family Handyman. Retrieved 3 February 2024.
  6. ^ "DASMA Metal Gauge Chart Technical Data Sheet #154" (PDF). DASMA. Archived from the original (PDF) on 2014-08-02. Retrieved 2015-07-19.
  7. ^ "DASMA Door and Access Systems Manufacturers Association". Dasma.com. 1993-01-01. Archived from the original on 2012-10-28. Retrieved 2012-11-04.
  8. ^ "DASMA Door and Access Systems Manufacturers Association". Dasma.com. Archived from the original on 2012-08-26. Retrieved 2012-11-04.
  9. ^ "How Important Are Garage Door Safety Sensors". rsvallejo.com. Retrieved 2023-04-06.
[edit]

Media related to Garage doors at Wikimedia Commons


A residential garage door opener. The motor is in the box on the upper-right.

A garage door opener is a motorized device that opens and closes a garage door controlled by switches on the garage wall. Most also include a handheld radio remote control carried by the owner, which can be used to open and close the door from a short distance.

The electric opener

[edit]

The electric overhead garage door opener was invented by C.G. Johnson in 1926 in Hartford City, Indiana.[1] Electric Garage Door openers did not become popular until Era Meter Company of Chicago offered one after World War II where the overhead garage door could be opened via a key pad located on a post at the end of the driveway or a switch inside the garage.[2]

As in an elevator, the electric motor does not provide most of the power to move a heavy garage door. Instead, most of door's weight is offset by the counterbalance springs attached to the door. (Even manually operated garage doors have counterbalances; otherwise, they would be too heavy for a person to open or close them.) In a typical design, torsion springs apply torque to a shaft, and that shaft applies a force to the garage door via steel counterbalance cables. The electric opener provides only a small amount of force to control how far the door opens and closes. In most cases, the garage door opener also holds the door closed in place of a lock.

The typical electric garage door opener consists of a power unit that contains the electric motor. The power unit attaches to a track. A trolley connected to an arm that attaches to the top of the garage door slides back and forth on the track, thus opening and closing the garage door. The trolley is pulled along the track by a chain, belt, or screw that turns when the motor is operated. A quick-release mechanism is attached to the trolley to allow the garage door to be disconnected from the opener for manual operation during a power failure or in case of emergency. Limit switches on the power unit control the distance the garage door opens and closes once the motor receives a signal from the remote control or wall push button to operate the door.[3]

The entire assembly hangs above the garage door. The power unit hangs from the ceiling and is located towards the rear of the garage. The end of the track on the opposite end of the power unit attaches to a header bracket that is attached to the header wall above the garage door. The powerhead is usually supported by punched angle iron.

Recently another type of opener, known as the jackshaft opener, has become more popular.[when?] This style of opener was used frequently on commercial doors but in recent years has been adapted for residential use. This style of opener consists of a motor that attaches to the side of the torsion rod and moves the door up and down by simply spinning the rod. These openers need a few extra components to function safely for residential use. These include a cable tension monitor, to detect when a cable is broken, and a separate locking mechanism to lock the door when it is fully closed. These have the advantage that they free up ceiling space that an ordinary opener and rail would occupy. These also have the disadvantage that the door must have a torsion rod to attach the motor to.

Types

[edit]

There are five types of garage door openers:

  1. Chain drive openers. These have a chain (similar to a bicycle's) that connects the trolley to the motor.
  2. Belt drive openers use a rubber belt in place of a chain.
  3. Screw drive openers have a long screw inside the track. The trolley connects to this screw.
  4. Direct drive openers have the motor installed inside the trolley and use a gear wheel to guide the trolley along a fixed chain.
  5. Jackshaft openers mount on the wall at either end of the torsion bar.

Remote control

[edit]

The first wireless garage door openers were invented and developed by two US inventors at the same time, one in Illinois and the other in Washington state, around 1930. They were unknown to each other.[4]

The first garage door opener remote controls were simple and consisted of a simple transmitter (the remote) and receiver which controlled the opener mechanism. The transmitter would transmit on a designated frequency; the receiver would listen for the radio signal, then open or close the garage, depending on the door position. The basic concept of this can be traced back to World War II. This type of system was used to detonate remote bombs. While novel at the time, the technology ran its course when garage door openers became popular. While the garage door remote control transmitter is low power and has limited range, its signal can be received by other, nearby, garage door openers. When two neighbors had garage door openers, then opening one garage door might open the neighbor's garage door as well.

The second stage of the wireless garage door opener system solved the opening-the-neighbor's-garage-door problem. The remote controls on these systems transmitted a digital code, and the receiver in the garage responded only to that code. The codes were typically set by eight to twelve DIP switches on the receiver and transmitter, so they allowed for 28 = 256 to 212 = 4,096 different codes. As long as neighbors used different codes, they would not open each other's garage doors. The intent of these systems was to avoid interference with nearby garage doors; the systems were not designed with security in mind. Intruders were able to defeat the security of these systems and gain entry to the garage and the house. The number of codes was small enough that even an unsophisticated intruder with a compatible remote control transmitter could just start transmitting all possible codes until he found one that opened the door. More sophisticated intruders could acquire a black box master key that automatically transmitted every possible code in a short time. An even more sophisticated method is known as a replay attack. The attacker would use a code grabber, which has a receiver that captures the remote's digital code and can retransmit that digital code at a later time. The attacker with a code grabber would wait nearby for the homeowner to use his remote, capture the code, and then replay the code to open the door when the homeowner was gone. Multicode openers became unpopular in areas where security was important, but due to their ease of programming, such openers are often used to operate such things as the gates in gated apartment complexes.

An intermediate stage of the garage door opener market eliminated the DIP switches and used remotes preprogrammed to one out of roughly 3.5 billion unique codes. The receiver would maintain a security list of remotes to which it would respond; the user could easily add the unique remote's code to the list by pressing a button on the garage door opener while activating the remote control. A large number of codes made the brute force try-all-possible-digital-codes attacks infeasible, but the systems were still vulnerable to code grabbers. For user convenience, these systems were also backward compatible with the older DIP switch remote codes, but adding an old technology remote to the security list made the garage door opener vulnerable to a brute force attack to find the DIP switch code. The larger code space approach was an improvement over the fixed DIP switch codes but was still vulnerable to the replay attack.

The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.

The fourth stage of garage door opener systems is similar to third stage, but it is limited to the 315 MHz frequency. The 315 MHz frequency range avoids interference from the land mobile radio system (LMRS) used by the U.S. military.

The following standards are used by units manufactured by Chamberlain (including LiftMaster and Craftsman):

Dates System Color of programming button and LED on unit Color of LED on remote*
1984–1993 8-12 DIP switch on 300-400 MHz white, gray, or yellow button with red LED red
1993–1997 Billion Code on 390 MHz green button with green or red LED green
1997–2005 Security+ (rolling code) on 390 MHz orange or red button with amber LED amber or none
2005–present Security+ (rolling code) on 315 MHz purple button with amber LED none
2011–present Security+ 2.0 (rolling code) on 310, 315, and 390 MHz yellow button with amber LED and yellow antenna wires red or blue

* Does not apply to keyless entry keypads or universal remotes.

Recent Chamberlain garage door openers that have Security+ 2.0 features also use a special serial protocol on wired connections rather than a simple switch closure.[5]

The following standards are used by units manufactured by Overhead Door Corporation and its subsidiary The Genie Company†:

Dates System
1985–1995 9–12 DIP switch on 360, 380, or 390 MHz[6][7]
1995–2005 Intellicode/CodeDodger (rolling code) on 390 MHz
2005–present Intellicode/CodeDodger (rolling code) on 315 MHz
2011–present Intellicode 2/CodeDodger 2 (rolling code) on 315 and 390 MHz

Note: There are no standard color codes for the learn button or LED on units manufactured by Overhead Door or Genie. All accessories made for later versions of Genie Intellicode and Overhead Door CodeDodger are backward compatible with previous generations of Intellicode and CodeDodger.

Cloning garage door opener remotes

[edit]
A typical photo of both the outer case and inner circuit of a garage door opener remote control.

Many garage door opener remote controls use fixed-code encoding which use DIP switches or soldering to do the address pins coding process, and they usually use pt2262/pt2272 or compatible ICs. For these fixed-code garage door opener remotes, one can easily clone the existing remote using a self-learning remote control duplicator (copy remote) which can make a copy of the remote using face-to-face copying.

Additional features

[edit]

Additional features that have been added over the years have included:

  • Automatic courtesy lights that turn on when the door opens (or via motion sensors) and automatically turn off after a preset delay
  • A remote lockout feature, which turns off the radio receiver while one is on vacation or away for an extended time.
  • The availability of accessories has increased, including such features as wireless keypads, key chain remotes, and solenoid-operated deadbolts to lock the door itself.
  • Automatic door closing feature, which after a fixed time by the owner, closes the garage door to prevent theft.

More sophisticated features are also available, such as an integrated carbon monoxide sensor to open the door in case of the garage being flooded with exhaust fumes. Other systems allow door activation over the Internet to allow home owners to open their garage door from their office for deliveries.

Another recent innovation in the garage door opener is a fingerprint-based wireless keypad. This unit attaches to the outside of the garage door on the jamb and allows users to open and close their doors with the press of a finger, rather than creating a personal identification number (PIN). This is especially helpful for families with children who may forget a code and are latchkey kids.

Safety

[edit]
Electric eye for safety

The garage door is generally the largest moving object in a home. An improperly adjusted garage door opener can exert strong and deadly forces and might not reverse the garage door in an emergency. The manufacturer's instructions provide guidance to the user on the proper adjustment and maintenance of the opener.

Garage door openers manufactured and installed in the United States since 1982 are required to provide a quick-release mechanism on the trolley that allows for the garage door to be disconnected from the garage door opener in the event of entrapment.[8] Garage door openers manufactured since 1991 are also required to reverse the garage door if it strikes a solid object.[9][10]

In the United States, the Consumer Product Safety Improvement Act of 1990 required that automatic residential garage door operators manufactured on or after 1 January 1991 conform to the entrapment protection requirements of the 1988 version of ANSI/UL standard 325.[11] A requirement for redundant entrapment-prevention devices was added in 1993; such a system can use an electric eye, a door edge sensor, or any other device that provides equivalent protection by reversing the travel of the closing door if an object is detected in its path.[12][13]

California Senate Bill No. 969

[edit]

In California, Senate Bill No. 969 requires that any automatic residential garage door opener that is manufactured for sale, sold, offered for sale, or installed in a residence to have a battery backup function that is designed to operate when activated because of an electrical outage.[14] The bill went into effect on July 1, 2019. Under the bill, any automatic garage door opener that is in violation is subject to a civil penalty of $1000.

The bill was passed by Gov. Jerry Brown on Sept. 21, 2018, in response to the 2017 California Wildfires in which at least 5 individuals lost their lives because they could not open their garage door when the power went out.[15]

The Door and Access Systems Manufacturers Association International opposed the bill arguing that garage door openers with backup batteries require regular maintenance and that the bill should be amended to make this clear. In addition, they said that "garage door openers with backup batteries are not designed to serve as life safety devices, and should not be relied upon to prove a means of egress from a garage during an electrical outage."[16]

The bill passed, despite most garage doors having a release pull cord.

References

[edit]
  1. ^ Robert J Girod (2014). "Garage Door Openers - High-tech Burglary". Advanced Criminal Investigations and Intelligence Operations: Tradecraft Methods, Practices, Tactics, and Techniques. Taylor and Francis. p. 90. ISBN 9781482230741.
  2. ^ "Aids To Modern Living - Garage Doors". Popular Science: 137. December 1946.
  3. ^ Castro, Diane. "The Complete Garage Door System". Regency Conference Center. Retrieved 10 March 2020.
  4. ^ "Widely Separated Inventors Invent Garage Door Openers By Radio Impulses". Popular Science: 32. February 1931.
  5. ^ "Will my older accessories work with the new line of Security+ 2.0 garage door openers?". alldaygaragerepair.com. Retrieved 2017-06-23.
  6. ^ Willmes, Dave. "My Overhead Door Opener Doesn't Work with this Universal Remote". www.overheaddooronline.com. Retrieved 20 October 2016.
  7. ^ "FCC ID BSH8YN106546 by Overhead Door Corporation". FCCID.io. Retrieved 20 October 2016.
  8. ^ "Falling Garage Doors — A Crushing Concern". Garage Door Child Safety.
  9. ^ "Non Reversing Garage Door Openers a Hazard" (PDF). U.S. Consumer Product Safety Commission.
  10. ^ "Garage Door System Safety Guidelines". Door & Access Systems Manufacturers Association International. Archived from the original on 2008-12-23.
  11. ^ Garage Door Operators • CPSC
  12. ^ Non-Reversing Automatic Garage Door Openers Are a Hazard • CPSC
  13. ^ 16CFR1211
  14. ^ "Bill Text - SB-969 Automatic garage door openers: backup batteries". leginfo.legislature.ca.gov. California Legislative Information. Retrieved 6 September 2019.
  15. ^ "New California Law Could Cost You $1000 in Fines". Clark's Garage Door. 4 September 2019. Retrieved 6 September 2019.
  16. ^ "California Mandates Battery Backup With All GDOS - Experts Cite Problems With The Legislation" (PDF). dasma.com. DASMA. Retrieved 6 September 2019.
[edit]

Driving Directions in Will County to


Driving Directions From Golden Corral Buffet & Grill to
Driving Directions From Honorable Thomas A Dunn to
Driving Directions From First American Bank to
Driving Directions From Joliet to
Driving Directions From Al's Steak House Restaurant to
Driving Directions From Pep Boys to
Driving Directions From Dollar General to