Intuitive operation, high productivity, heavy-duty bend performance, and high productivity all in one cost-effective package
In addition to being industry-leading in production, our machines also come equipped with intuitive operator control that takes the stress out daily operation for operators of all skill levels.
Every Standard hydraulic presse brake is checked in Rockford Illinois by our Perfect Machine Process to ensure it is ready for installation in your shop.
Flexible and reliable bending performance with patented HEXA-C® frame – all in a cost-efficient package.
There are many options with our high end precision press brakes. These include better controls, more setups, faster part production and large daylight openings. A stable, fast AC servo-motor-driven back gauge system is featured. Outboard mounted long Ram guides are also available (which offer stability while still allowing for full length between the frames) to aid in acute angle bending.
Warning: incorrect tonnage, which is too high or low, can cause damage or irreparable injury to your press brake. Refer to the manual or a table to calculate the weight of your press brake.
Hydraulic Piston Press For Bicycle Disc Brakes
Press brakes are a necessity to almost any metal fabrication shop. Unfortunately, despite being one of the most important and desired pieces of machinery in a shop, they’re still misunderstood—even by professionals. To help you better understand press brakes, we put together this short, layman’s-level guide.
High productivity, heavy-duty bending performance, and intuitive operation – all in a cost-efficient package
Our high-end precision press brakes have many possibilities. They offer more controls, faster setups and production, as well as large daylight openings and larger working areas. Other features include a fast AC-servo motor-driven backgau system that is stable and reliable, as well as outboard mounted long RAM guides (which are long enough to reach all the frames and allow for precise angle bending)
Before choosing a press brake, you need to first identify the type of metal that you wish to bend (stainless, 16-gauge mild steel, etc.).
This method allows for high levels of angular precision. This method can be used for sheet metal greater than 2mm thick.
In bottom bending, the punch curves the metal sheet with a high force (3 to 5 times greater than air bending) which reduces or even prevents the spring back effect generally associated with air bending. The process begins with air bending then continues with cold forging carried out at the bottom of the V.
This revolutionary tool changer gives press brake operators real-time information to help them perform better.
The motor within a mechanical press brake works by turning a large flywheel. The motor spins a large flywheel at high speed. The flywheel is controlled by the machine operator through a clutch. This sets the other parts in motion to bend metal. The mechanical press brake is simpler, especially in terms of its electronics. This makes maintenance and operation much easier. The mechanical press brakes can handle tons up to three times their intrinsic rating. Mechanical press brakes have one major drawback: the ram must go through a complete cycle once it is engaged. This cannot be reversed. This poses safety risks if an operator makes a mistake or places limitations on the machine. The possibility that the press brake could become locked if too much ram travel is one potential danger.
Rare earth magnets can withstand pressures up to 9,000 lbs per square inch, but not for what you might think. The Internet has seen hydraulic presses crush things for a while.
With about 70 lbs, the average person can push on the brake pedal. You can apply the brake pedal with about 70 lbs. To stop a moving vehicle disc brakes require 800-1200 psi at their calipers. All parts of the system amplify the force you apply to the pedal.
Hydraulic brakes use brake fluid within sealed tubing between the lever and caliper. This fluid is usually either DOT fluid, or mineral oil/fluid. Both fluids can cause contamination over time so it is important to flush the system and have fluid changed periodically.
Hydraulic presses brakes can be used to bend or fold metal by pressing it into dies. These presses can be used for both sheet metal work and continuous production. These presses can handle difficult industrial production jobs, from single-cycle operations to automated components.
Axis Description Axis Explanation X2 Right stop finger backward and forth moving the axis R1 left end stop finger up-and-down moving the axis Z1 right end stop finger left-and right moving the axis 5 additional rows.