Tube Laser Cutting Systems Uses

Tube Laser Cutting Systems New Zealand

Many believed that fiber lasers were only suitable for thin materials. Because of its longer wavelength, CO2 created enough kerf to allow for material removal. The fiber laser could not produce the same results or kerf with thicker materials. This problem has been solved by collimating technology, which can create a wider fiber laser-generated beam. This allows for materials separation and more room to remove thicker materials. The machine can switch between the beam widths, so it can process thinner materials with the narrower beam. This allows for faster processing of different-sized materials using the same fiber laser cutting machine.

Fiber lasers require little maintenance, are more efficient than traditional CO2 laser cutting machines and can cut reflective materials. They are also faster than CO2 machines for certain metal thicknesses. When it comes to cutting tubes, speed is not necessarily a good thing. You can save time by speeding up the tube processing and producing finished parts.

Imagine putting a through hole centered on a tube. It should be centered according to the actual dimension and not just one side of the tube. Bowed tubes will make it more difficult. Tube fabricating is hard work.

The fiber laser requires less maintenance than a CO2 laser. The fiber laser does not need the mirror cleaning or bellows checking that a CO2 cutting machine requires. The fiber laser doesn't need any preventive maintenance, provided it receives clean chiller and cooling water.

Tube Laser Cutting Systems 24 X 12

Tube Laser Cutting Systems 24 X 12

Motion Dynamics is a leader in the manufacture of neuro-sub-assemblies. This includes steerable catheters, "pull-wire" assemblies and other neurological components. We use our StarCut Tube machines to precisely cut key components.

You don't need to spend a lot of money or be very technical in order to have your own laser tube cutting. Anybody can cut like no one has ever seen, from students to engineers.

Tube Laser Cutting Machine Trumpf

All types and all shapes: This 3-dimensional cutting machine cuts carbon, aluminum, stainless, and red metals. It is available in round, rectangular, irregular and square shapes.

Perhaps you have noticed that we haven’t yet discussed cutting speed. Although it is possible to cut 500 inches per minute with a tube, this is not always feasible. Laser tube cutting should not be about how long it takes for a tube to be loaded, indexed so that it is in the right place for cutting, pierce it and then unload it. Laser tube cutting machines are more concerned with part-processing times than cutting speed.

Tube Laser Cutting Machine Trumpf

Tube Laser Cutting System Hs Code

Fiber lasers are nearly maintenance-free and demonstrate superior wall plug efficiency compared to traditional CO2 Laser cutting machines. They can also be used for precise cutting of reflective materials. They are faster than CO2 when cutting certain thicknesses of steel. The speed of cutting tube is relative. Real time savings can be achieved by speeding up processing times for the tube and creating finished parts.

What can you do to compensate? You will traditionally touch your face with a sensor to mark the contact point. The tube is then turned and touched on the other side. This gives the control an indication of how bent the tube is. This is a reliable method that can guarantee the through-holes are working for the application. However, this method reduces the ability to deliver extremely high tolerances for each rotation of the tube.

Tube Laser Cutting Systems New Zealand
Tube Laser Cutting Systems 3mm

Because of the amount of power required to create a CO2 laser, it is less efficient and has a much lower wall plug efficiency when compared to a fiber laser. It follows that the large chillers required for the CO2 lasers need more overall power too. Given the fiber laser resonator’s wall plug efficiency of more than 40 percent, you are not only using less power, but also less of your in-high-demand floor space.

Keep in mind that there is no such thing as a perfect tube. They have bows. Weld seams can protrude not only on the exterior but also the interior of the tube. It’s a real challenge to process this material consistently and rapidly when such inconsistencies exist from one product run to another.

Tube Laser Cutting Machine Trumpf
Tube Lasers Cutting Systems 101

We offer you the ideal solutions for the world of laser tube cutting. Find out here how lasers can eliminate entire process steps while also increasing the range of parts you can produce.

The high cutting speed of CO2 lasers is what makes them stand out. Their main application area is the medium-to-high range of material thicknesses. The laser beam cuts with high precision and is free from burrs. This allows the parts to be processed further without needing to be reworked.