Tube Lasers Cutting Systems Minneapolis

Tube Laser Cutting Systems Model 40268

Most metal fabricators have a strong understanding of what fiber laser cutting technology has done for flat sheet processing, but just what has the fiber laser done for tube cutting? Quite a bit, actually.

Another consideration is the fiber laser’s briefcase-sized modules—they allow for redundancy. If one module has a problem, the resonator doesn’t shut down completely. The fiber laser is redundant in a way that the other modules can produce more power temporarily to support the down module until repairs can be completed—which, by the way, can be done in the field. Other times the fiber resonator can continue producing reduced power until repairs can be made. Unfortunately, if a CO2 resonator has an issue, the entire resonator is down, not just in a reduced-power mode.

Tube Laser Cutting Systems Model 40268

This machine can be used for processing XXL-sized tubes. This machine, which is a solid state laser, can be used in many ways to make tubes and profiles.

Lasertube allows you to make suggestions for improvements to your customers' parts design. The extensive library of connections can be used for assembly without the use of screws or welding.

Tube Laser Cutting Systems 2018

Tube Laser Cutting Systems 2018

The CO2 resonator requires much more energy and is larger. Electricity is used to combine gases to create the laser beam. Mirrors aid in the light's intensity and prepare it for exiting the resonator. The beam must travel along a path that includes several cooled mirrors to reach the lens after it has exited the resonator. This causes the beam to lose power and quality.

A laser cutter that cuts sheet metal can transform a sheet of paper in seconds. You can also do the same with a laser tube cutter machine but it is a completely different story about how it is done.

When should I replace my CO2 laser tube

How do you compensate for that? Traditionally, you are going to come down and touch the face with a sensor that marks the contact point. The tube is then rotated, and the opposite side of the tube is touched. That gives the control an idea of just how bowed the tube is. This method is accurate and can ensure those through-holes work out for the application. But keep in mind that each time a rotation of the tube occurs, the ability to deliver very high tolerances is reduced.

Some things are very obvious. A fiber laser's laser generator is smaller than a CO2 resonator. The fiber laser is actually made from banks of diodes, which are assembled in a module the size of a briefcase. It can produce power from 600 to 1,500 Watts. The final powered resonator is made up of multiple modules that are connected together. It can be as small as a small filing cabinet. Fiber-optic cable amplifies the light produced and channels it. The light that exits the fiber optic cable is exactly the same as it was when it was generated. There is no loss in power or quality. The light is then focused and adjusted to determine the material that will be cut.

When should I replace my CO2 laser tube

Laser Pipe Cutting Machine Video

Let's take a look at the benefits of an automated tube and section bar storage with a Lasertube cutter system.

The CO2 solution for large diameter tubes and profiles.Tubes up to Ø 14" / 24" (355 mm / 610 mm)3D cutting modeCO2 laser

Tube Laser Cutting System 6.3.731.8

Laser tube cutting machines do not have standard material towers. Bundle loaders provide the fastest method of handling tube material. One tube is fed from a bundle into the tube laser by a singularizing system. This type isn't able to feed open profiles like angles and channels. They interlock in the bundle and are not easy to get free. Step loaders can be used to sequence open profiles one by one into the machine, while still maintaining the proper orientation.

There is no shortage of variety in any job shop. Parts of various sizes are not uncommon when you use one tube. The machine should be able unload laser-cut pieces as small as 2in. It can also be extended up to 15 feet, one after the other. It must also be in a position to lift the parts and not damage them. This is often a problem for aluminum or other softer metals.

When should I replace my CO2 laser tube

Check our other pages :

Gauge

Imagine that you have to position a through-hole on top of a tube. It must be centered on the tube's actual dimension. It will be more difficult to center the tube if it is bent. This is the reality of tube fabrication.

When fabricators think of fiber laser cutting technology they may first think high-speed. This might be true. However, speed is subjective when it comes to tube-cutting. It's not the cutting speed of the tube that matters, but rather the processing time.